Joined in 2023 
82 
63 About this deal
Find out more about the FA3820X4 CO Alarm. FA3313X4: Carbon Monoxide Alarm with replaceable batteries With our sleep easy function, you can silence low battery chirps for 8 hours, up to 10 times. This feature not only allows you to enjoy a silent night’s sleep, but gives you vital time to take action and replace your batteries. If your alarm is not a sealed battery alarm, then install the batteries following the steps within the manual. Find out more about what you should expect from your landlord for CO safety in your home. Get protected today
We recommend you clean your smoke and heat alarms every 3 months to stop a build-up of dust or insect webs from preventing the sensor to work correctly. To activate your CO alarm, pull the disabling tab out of the alarm and wait up to 1 minute for the green LED to flash to confirm the alarm is active. After 1 minute, press the test button to hear the alarm sound. Please note, the alarm will not sound before the 1 minute activation period is complete. CO alarms and rental properties The FA6813-EU offers electrochemical sensing technology and a clear loud alarm to ensure trusted carbon monoxide (CO) detection for your home. This alarm also features our new Crescendo Test, which helps to protect your hearing by allowing you to choose the volume level of the test alarm. Simply hold down the test button and the alarm will move through the increasing volume levels (similar to a rising ‘crescendo’) until you find the alert sound level you are comfortable with. A common cause of nuisance alarms is the incorrect positioning of a smoke or heat alarm. If your FireAngel alarm has begun chirping not long after installation, make sure it is fitted in the right room in your home. Under the extended Smoke and Carbon Monoxide Alarm (England) Regulations 2015, from October 1st 2022, a carbon monoxide alarm will be required in all rooms where there is a fixed combustion appliance – such as gas boilers or gas fires – once the compliance date is announced. However, gas cookers are excluded from the updated regulation.Where your alarm is installed can also trigger nuisance alarms if not correctly placed, for example too close to doors or windows. Guidance for where to install your smoke, heat and CO alarms can be found below. With low level CO monitoring, a pre-alarm warning to open windows helps reduce the risk of CO poisoning and prevents build-up of dangerous CO levels. If a room is not ventilated and ppm levels continue to increase, the alarm will activate. If there is a partition in a room, the alarm should be located on the same side of the partition as the potential source. Find out more about the FA3313X4 CO Alarm. FA6813-EU: Carbon Monoxide Alarm with replaceable batteries FireAngel’s FA3322 digital carbon monoxide alarm features many icons on the LCD screen. View our guide below to help you understand what each represents.
An audible Carbon Monoxide detector is the only way to be alerted to a carbon monoxide leak; it can’t be smelt, tasted or seen so it’s impossible for human senses to detect. All alarms are calibrated and rigorously tested in-house and are third party tested to receive the BSI Kitemark certification to provide peace of mind. Also, the new range is compliant with the revised European Standard EN 50291-1:2018 to ensure maximum protection. FA3322X4: Carbon Monoxide Alarm with digital display and 10 year battery Looking for a CO-9D alarm replacement? FireAngel’s new FA3322X4 alarm will be replacing any end-of-life CO-9D alarms. With a multi-functional LCD digital display and array of exclusive features such as Alarm Memory, Ventilate Instruction, Quiet Self Test and Environmental Sensing, the FA3322X4 offers the highest level of CO detection for your home. The below provides an overview of installing your carbon monoxide alarm, but please refer to each alarm’s manual for tailored guidance. Which room can I install this carbon monoxide alarm?Our FA3322X4 Carbon Monoxide Alarm with digital display comes with a sealed, tamper proof battery that will last the lifetime of the alarm. The sensors within the unit will deteriorate after 10 years, so to ensure you’re protected we recommend you replace the unit after this time. Carbon monoxide alarms in rooms with sloped ceilings should be located at the high side of the room. The alarm comes with 2 X AA batteries that can be replaced once the low battery chirp can be heard. FireAngel’s new range of carbon monoxide alarms use intelligent sensing technology for a rapid reaction to rising levels of CO.
These alarms fall under the Waste Electrical and Electronic Equipment regulations (WEEE). The directive requires producers of Electronic Equipment to join a WEEE compliance scheme and contribute to the cost of recycling Waste Electronic Equipment that is collected at local recycling centres and other routes. The alarm features the latest CO sensing technology and can be used to replace end-of-life FireAngel CO-9X alarms. Fitted with a sealed, tamper proof battery that will last the lifetime of the alarm. The sensors within the unit will deteriorate after 10 years, so to ensure you’re protected we recommend you replace the unit after this time. FireAngel recommend a CO alarm is installed between 1 m and 3 m away from each fuel‑burning appliance, as well as installing additional units in areas such as living rooms and bedrooms where you spend most time whilst at home. Activating your new FireAngel CO alarm However, if you notice any visible damage to the alarm during cleaning, including any severe staining or dust, we recommend you replace the alarm as the sensor within could be damaged. Does cleaning my alarm really help stop the beeping? Using a soft brush adaptor, your vacuum or your hairdryer on a cool setting, run along the edges and face of the alarm. Please do not use any solvents or cleaners on your alarm as they may cause damage to the sensor or circuitry.Alarms located in sleeping rooms and in rooms without a fuel-burning appliance should be located relatively close to the breathing zone of the occupants. Read our handy guide for more information on correctly installing your alarms or discover why your Pro Connected alarms may be beeping in our guide. Dust contamination: How do I clean my alarm? The alarm’s high sensitivity mode will be enabled if the alarm predicts CO levels will increase to or above 180ppm for fast reaction to rising CO levels. Remove the disabling clip by pulling it out of the alarm and retain the disabling tab for future use.
Known as the ‘ Silent Killer’, CO occurs when fuels burn incompletely, with common sources being boilers, gas fires and hobs and solid fuel burners. However, carbon monoxide can also pass through walls, so you would also be at risk if a neighbouring property had a leak. We have been monitoring it since and I’m pleased to say that the issue appears to have been resolved so no requirement to issue a replacement.I completed everything that you advised by cleaning any dust on the alarm and banging in the palm of my hand to dislodge anything. With the alarm memory function, the red LED will flash to provide a visual indication of a previous CO alarm activation. For alarms located in the same room as a fuel-burning appliance (for both wall and ceiling mounted alarms) the following applies:
Related:
Great Deal 
New Comment